TZT DC 5V MQ-9 Combustible Gas Detector Carbon Monoxide CO Sensor Module for Arduino
Published: 11.05.2024 In stock: 179713 745 Views
Description
Product Overview:
Sensitive material MQ-9 gas sensors used in clean air, low conductivity tin oxide (SnO2). High-low temperature cycling detection mode (1.5V heating) detecting carbon monoxide sensor's conductivity increases with the air of carbon monoxide gas concentration increases, spurious adsorption at high temperature (5.0V heat) detection of combustible gases methane, propane, and cryogenic cleaning gas. Using a simple circuit to change the conductivity, concentration of the gas is converted to the corresponding output signal. MQ-9 gas sensor for high carbon monoxide, methane, liquefied petroleum gas sensitivity, this sensor can detect a variety of carbon monoxide and combustible gas, is a low-cost sensor suitable for a variety of applications.
Application:
Suitable for home or industrial hydrogen leak monitoring devices. Can not interfere with ethanol vapor, soot, carbon monoxide and other gases.
Features:
- Using high-quality dual-panel design,with power indicator and TTL signal output instructions.
- The switching signal having a DO (TTL) output and analog output AO.
- TTL output valid signal is low. ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
- Analog output voltage with the higher concentration of higher voltage
- There are four screw holes for easy positioning.
- Has a long life and reliable stability
- Rapid response and recovery characteristic
Input voltage : DC5V Power consumption ( current ): 150mA
DO output : TTL digital 0 and 1 ( 0.1 and 5V)
AO output :0.1-0 .3 V ( relative to pollution ),the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered,needs to warm up around 20S,measured data was stable,heat sensor is a normal phenomenon,because the internal heating wire,if hot is not normal .
DO output : TTL digital 0 and 1 ( 0.1 and 5V)
AO output :0.1-0 .3 V ( relative to pollution ),the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered,needs to warm up around 20S,measured data was stable,heat sensor is a normal phenomenon,because the internal heating wire,if hot is not normal .
Wiring:
- VCC: positive power supply (5V)
- GND: power supply is negative
- DO: TTL switching signal output
AO: analog signal output
NOTE:
After the sensor is powered, need to warm about 20S, measured data becomes stable, heat sensor is normalSize:
Test program:Function: This version of the test program supportingUse chip: AT89S52Crystal: 11.0592MHZBaud rate: 9600Compiler Environment: Keil[Statement] This procedure is used only for study and reference, please indicate the copyright and author information!************************************************** ******************* // ************************************************* *******************Note: 1, when the measured concentration is greater than the set density, single-chip IO port output low************************************************** ******************* /# Include // library files#define uchar unsigned char // macro definition unsigned char#define uint unsigned int // macro definition unsigned int/ ************************************************* *******************I / O definitions************************************************** ******************* /sbit LED = P1 ^ 0; // define microcontroller P1 port of the first one (ie P1.0) to indicate the endsbit DOUT = P2 ^ 0; // define the microcontroller P2 port first one (ie P2.0) as an input sensor/ ************************************************* *******************Delay function************************************************** ******************* /void delay () // delay procedure{uchar m, n, s;for (m = 20; m> 0; m--)for (n = 20; n> 0; n--)for (s = 248; s> 0; s--);}/ ************************************************* *******************The main function************************************************** ******************* /void main (){while (1) // infinite loop{LED = 1; // off P1.0 port lightsif (DOUT == 0) // When the concentration is higher than the set value, the implementation of the Con{delay (); // delay interferenceWhen if (DOUT == 0) // determine the concentration higher than the set value, the implementation of the Con{LED = 0; // P1.0 port lights lit}}}}/ ************************************************* *******************End************************************************** ****************** /
Characteristics
Type
Gas SensorUsage
Gas SensorOrigin
Mainland ChinaOutput
Switching TransducerTheory
Hall SensorMaterial
MetalBrand Name
TZTModel Number
MQ-9is_customized
Yes